1 files changed, 0 insertions, 93 deletions
diff --git a/02.5-collatz/src/main.c b/02.5-collatz/src/main.c
deleted file mode 100644
index 5af52ed..0000000
--- a/02.5-collatz/src/main.c
+++ /dev/null
@@ -1,93 +0,0 @@
-
-#include "clock.h"
-#include "delay.h"
-#include "gpio.h"
-#include "spin.h"
-#include "usart.h"
-
-volatile uint32_t delay_amt = 20000000 / 4;
-
-int enable_usart2(uint32_t baud_rate)
-{
-  __IO gpio_port_t* port_a = enable_gpio(GPIO_PORT_A);
-  enable_hsi(&RCC, true);
-
-  // Turn on the clock for the USART2 peripheral
-  set_usart2_clock_src(&RCC, USART_CLK_SRC_HSI16);
-  set_usart2_clock_enabled(&RCC, true);
-
-  // Configure the I/O pins.  Will use PA2 as TX and PA15 as RX so setup for
-  // alternate function
-  set_gpio_pin_mode(port_a, PIN_2, MODE_ALTERNATE);
-  set_gpio_pin_mode(port_a, PIN_15, MODE_ALTERNATE);
-  set_gpio_alternate_function(port_a, PIN_2, AFN_7);
-  set_gpio_alternate_function(port_a, PIN_15, AFN_3);
-
-  // De-assert reset of USART2
-  RCC.apb1rst1_r &= ~BIT(17);
-
-  // Configure the USART
-  // disable USART first to allow setting of other control bits
-  // This also disables parity checking and enables 16 times oversampling
-
-  USART2.c_r1 = 0;
-  USART2.c_r2 = 0;
-  USART2.c_r3 = 0;
-
-  usart_set_divisor(&USART2, 16000000 / baud_rate);
-  usart_set_enabled(&USART2, USART_ENABLE_TX | USART_ENABLE_RX);
-}
-
-int enable_usart1(uint32_t baud_rate)
-{
-  /* Enable the GPIO bus. */
-  __IO gpio_port_t* port_b = enable_gpio(GPIO_PORT_B);
-
-  /* Enable the USART clock. */
-  RCC.apb2en_r |= BIT(14);
-
-  /* == Configure the IO Pins. == */
-
-  /* GPIO D5 (Port B pin 6) is USART1 Tx,
-   * GPIO D6 (Port B pin 7) is USART1 Rx. */
-  set_gpio_pin_mode(port_b, PIN_6, MODE_ALTERNATE);
-  set_gpio_pin_mode(port_b, PIN_7, MODE_ALTERNATE);
-
-  /* Set the GPIO pins to use the USART alternate function. */
-  set_gpio_alternate_function(port_b, PIN_6, AFN_7);
-  set_gpio_alternate_function(port_b, PIN_7, AFN_7);
-
-  RCC.apb2rst_r &= ~BIT(14); /* De-assert reset of USART1 */
-
-  uint32_t baud_rate_div = 80000000 / baud_rate;
-  USART1.c_r1 = 0;
-  USART1.c_r2 = 0;
-  USART1.c_r3 = 0;
-  USART1.br_r = baud_rate_div;
-
-  USART1.c_r1 |= BIT(3) | BIT(2);
-  USART1.c_r1 |= BIT(0);
-
-  /* Enable the transmitter and the receiver. */
-  usart_set_enabled(&USART1, USART_ENABLE_TX);
-  asm volatile(" cpsie i ");
-}
-
-/* Main function. This gets executed from the interrupt vector defined above. */
-int main()
-{
-  /* Enable the GPIO port B. */
-
-  __IO gpio_port_t* port_b = enable_gpio(GPIO_PORT_B);
-  gpio_output_pin_t pin3 = set_gpio_pin_output(port_b, PIN_3);
-  gpio_output_pin_t pin1 = set_gpio_pin_output(port_b, PIN_1);
-
-  /* Enable a higher clock frequency. */
-  set_system_clock_MHz(80);
-
-  enable_usart2(115200);
-
-  pin_on(pin3);
-  usart_transmit_str(&USART2, "Hello, World\n");
-  for(;;);
-}