diff options
Diffstat (limited to '02.5-collatz/src')
| -rw-r--r-- | 02.5-collatz/src/clock.c | 106 | ||||
| -rw-r--r-- | 02.5-collatz/src/delay.c | 9 | ||||
| -rw-r--r-- | 02.5-collatz/src/gpio.c | 52 | ||||
| -rw-r--r-- | 02.5-collatz/src/isr_vector.c | 165 | ||||
| -rw-r--r-- | 02.5-collatz/src/main.c | 93 | ||||
| -rw-r--r-- | 02.5-collatz/src/spin.c | 49 | ||||
| -rw-r--r-- | 02.5-collatz/src/usart.c | 80 | ||||
| -rw-r--r-- | 02.5-collatz/src/vector.c | 0 |
8 files changed, 0 insertions, 554 deletions
diff --git a/02.5-collatz/src/clock.c b/02.5-collatz/src/clock.c deleted file mode 100644 index 75bac97..0000000 --- a/02.5-collatz/src/clock.c +++ /dev/null @@ -1,106 +0,0 @@ -/* - * This file sets the system clock to its full glory of 80Mhz - */ - -#include "clock.h" -#include <stdint.h> -#include "flash.h" -#include "gpio.h" -#include "spin.h" - -#define TIMEOUT 10000 - -int pll_off() -{ - uint32_t c; - - RCC.c_r &= ~BIT(24); /* Turn off pll. */ - for (c = 0; c < TIMEOUT && RCC.c_r & BIT(25); ++c) - ; /* Wait for OFF. */ - - if (c == TIMEOUT) { - return E_TIMEOUT; - } - - return 0; -} - -int pll_on() -{ - uint32_t c; - - RCC.c_r |= BIT(24); /* Turn on PLL. */ - for (c = 0; c < TIMEOUT && !(RCC.c_r & BIT(25)); ++c) - ; /* Wait for RDY. */ - - if (c == TIMEOUT) { - return E_TIMEOUT; - } - - return 0; -} - -int configure_pll( - uint8_t pllp_div_factor, pll_divisor_t pllr, /* System clock divisor. */ - pll_divisor_t pllq, /* Divison factor for PLL48M1CLK. */ - pllp_divisor_t pllp, /* Divison factor for PLLSAI2CLK. */ - uint8_t plln, /* PLL numerator. */ - pllm_divisor_t pllm, /* PLL denominator. */ - pll_src_t pllsrc /* PLL source */) -{ - if (RCC.c_r & BIT(25)) { - /* PLL must be off to configure it. */ - return E_NOT_OFF; - } - - /* Make sure inputs are valid. */ - if (pllp_div_factor == 1 || pllp_div_factor > 31) { - return E_BADPLLP_DIV; - } - if (plln < 8 || plln > 86) { - return E_BADPLLN; - } - - RCC.pllcfg_r = (pllp_div_factor << 27) | (pllr << 24) | (pllq << 20) | - (pllp << 16) | (plln << 8) | (pllm << 4) | (pllsrc << 0); - - return 0; -} - -int set_system_clock_MHz(uint8_t mhz) -{ - /* Set the source of the system colck to MSI temporarily. */ - set_system_clock_src(SYSTEM_CLOCK_SRC_MSI); - - if (mhz <= 8 || mhz > 80) { - return E_BAD_ARG; - } - - pll_off(); - - configure_pll( - 0 /* pllp_div_factor */, PLL_DIVISOR_4 /* pllr: VCO / 4 = mhz MHz. */, - PLL_DIVISOR_4 /* pllq: VCO / 4 = mhz MHz */, PLLP_DIVISOR_7 /* pllp */, - - /* The following set the frequency of VCO to (mhz*4)MHz: mhz * 1 * 4MHz. - */ - mhz /* plln | mhz */, PLLM_DIVISOR_1 /* pllm | 01 */, - PLL_SRC_MSI /* pll src | 04 Mhz */); - - pll_on(); - - /* Configure the flash to have 4 wait states. This is required at - * 80 MHz. */ - FLASH.ac_r &= ~0x07; - FLASH.ac_r |= 0x04; - - /* Set the source of the system colck to PLL. */ - set_system_clock_src(SYSTEM_CLOCK_SRC_PLL); - return 0; -} - -int set_system_clock_src(system_clock_src_t src) -{ - uint8_t value = RCC.cfg_r & ~0x03; - RCC.cfg_r = value | src; -} diff --git a/02.5-collatz/src/delay.c b/02.5-collatz/src/delay.c deleted file mode 100644 index 2a16d47..0000000 --- a/02.5-collatz/src/delay.c +++ /dev/null @@ -1,9 +0,0 @@ -#include "delay.h" - -void delay(uint32_t delay) -{ - while (delay--) { - /* needed to keep the compiler from optimizing away the loop. */ - asm volatile(""); - } -} diff --git a/02.5-collatz/src/gpio.c b/02.5-collatz/src/gpio.c deleted file mode 100644 index 02933b7..0000000 --- a/02.5-collatz/src/gpio.c +++ /dev/null @@ -1,52 +0,0 @@ -#include "gpio.h" -#include "rcc.h" - -/* - * Sets the mode of a pin on a gpio por. - */ -void set_gpio_pin_mode( - __IO gpio_port_t* gpio_port, gpio_pin_t pin, gpio_pin_mode_t mode) -{ - /* Each pin has a 2-bit mode provided at bits pin#*2 and pin#*2+1 */ - gpio_port->mode_r &= ~(0x03 << pin * 2); - gpio_port->mode_r |= mode << pin * 2; -} - -gpio_output_pin_t set_gpio_pin_output( - __IO gpio_port_t* gpio_port, gpio_pin_t pin) -{ - set_gpio_pin_mode(gpio_port, pin, MODE_OUTPUT); - - return (gpio_output_pin_t){.gpio_port = gpio_port, .pin = pin}; -} - -void set_gpio_output_pin(gpio_output_pin_t pin, bool onoff) -{ - if (onoff) { - pin.gpio_port->output_r |= 1 << pin.pin; - } else { - pin.gpio_port->output_r &= ~(1 << pin.pin); - } -} - -void set_gpio_alternate_function( - __IO gpio_port_t* port, gpio_pin_t gpio_pin, alternate_function_t afn) -{ - __IO uint32_t* reg; - if (gpio_pin < 8) { - reg = &(port->af_rl); - } else { - reg = &(port->af_rh); - gpio_pin -= 8; - } - - uint32_t tmp = *reg & (~0x0f << gpio_pin * 4); - *reg = tmp | (afn << gpio_pin * 4); -} - -#define GPIO_PORTS_BASE_ADDR ((uint8_t*)0x48000000) -__IO gpio_port_t* enable_gpio(gpio_port_number_t gpio_port_number) -{ - RCC.ahb2en_r |= 1 << gpio_port_number; /* Enable the GPIO port. */ - return (__IO gpio_port_t*)(GPIO_PORTS_BASE_ADDR + (gpio_port_number * 0x400)); -} diff --git a/02.5-collatz/src/isr_vector.c b/02.5-collatz/src/isr_vector.c deleted file mode 100644 index ab38dc2..0000000 --- a/02.5-collatz/src/isr_vector.c +++ /dev/null @@ -1,165 +0,0 @@ -#include "isr_vector.h" -#include "delay.h" -#include "gpio.h" - -/* Forward-declare the main function. This is implemented in main.c. */ -void main(); - -/* These are defined in the linker script. */ -extern uint32_t INIT_DATA_VALUES; -extern uint32_t DATA_SEGMENT_START; -extern uint32_t DATA_SEGMENT_STOP; -extern uint32_t BSS_START; -extern uint32_t BSS_END; - -/* - * Runs before main. Initializes the data and bss segments by loading them - * into memory. - */ -void init() -{ - uint32_t* src; - uint32_t* dest; - - src = &INIT_DATA_VALUES; - dest = &DATA_SEGMENT_START; - - /* Copy the values from flash into the data segment. */ - while (dest != &DATA_SEGMENT_STOP) { - *(dest++) = *(src++); - } - - /* Everything in the BSS segment is set to zero. */ - dest = &BSS_START; - while (dest != &BSS_END) { - *(dest++) = 0; - } - - /* Jump to main. */ - main(); -} - -const void* vectors[] __attribute__((section(".vectors"))) = { - (void*)0x2000c000, /* Top of stack at top of sram1. 48k */ - init, /* Reset handler */ - unhandled_isr, /* NMI */ - unhandled_isr, /* Hard Fault */ - unhandled_isr, /* MemManage */ - unhandled_isr, /* BusFault */ - unhandled_isr, /* UsageFault */ - unhandled_isr, /* Reserved */ - unhandled_isr, /* Reserved */ - unhandled_isr, /* Reserved */ - unhandled_isr, /* Reserved */ - unhandled_isr, /* SVCall */ - unhandled_isr, /* Debug */ - unhandled_isr, /* Reserved */ - unhandled_isr, /* PendSV */ - unhandled_isr, /* SysTick */ - - /* External interrupt handlers follow */ - unhandled_isr, /* 0 WWDG */ - unhandled_isr, /* 1 PVD */ - unhandled_isr, /* 2 TAMP_SAMP */ - unhandled_isr, /* 3 RTC_WKUP */ - unhandled_isr, /* 4 FLASH */ - unhandled_isr, /* 5 RCC */ - unhandled_isr, /* 6 EXTI0 */ - unhandled_isr, /* 7 EXTI1 */ - unhandled_isr, /* 8 EXTI2 */ - unhandled_isr, /* 9 EXTI3 */ - unhandled_isr, /* 10 EXTI4 */ - unhandled_isr, /* 11 DMA_CH1 */ - unhandled_isr, /* 12 DMA_CH2 */ - unhandled_isr, /* 13 DMA_CH3 */ - unhandled_isr, /* 14 DMA_CH4 */ - unhandled_isr, /* 15 DMA_CH5 */ - unhandled_isr, /* 16 DMA_CH6 */ - unhandled_isr, /* 17 DMA_CH7 */ - unhandled_isr, /* 18 ADC1 */ - unhandled_isr, /* 19 CAN_TX */ - unhandled_isr, /* 20 CAN_RX0 */ - unhandled_isr, /* 21 CAN_RX1 */ - unhandled_isr, /* 22 CAN_SCE */ - unhandled_isr, /* 23 EXTI9_5 */ - unhandled_isr, /* 24 TIM1_BRK/TIM15 */ - unhandled_isr, /* 25 TIM1_UP/TIM16 */ - unhandled_isr, /* 26 TIM1_TRG_COM */ - unhandled_isr, /* 27 TIM1_CC */ - unhandled_isr, /* 28 TIM2 */ - unhandled_isr, /* 29 Reserved */ - unhandled_isr, /* 30 Reserved */ - unhandled_isr, /* 31 I2C1_EV */ - unhandled_isr, /* 32 I2C1_ER */ - unhandled_isr, /* 33 I2C2_EV */ - unhandled_isr, /* 34 I2C2_ER */ - unhandled_isr, /* 35 SPI1 */ - unhandled_isr, /* 36 SPI2 */ - unhandled_isr, /* 37 USART1 */ - unhandled_isr, /* 38 USART2 */ - unhandled_isr, /* 39 USART3 */ - unhandled_isr, /* 40 EXTI15_10 */ - unhandled_isr, /* 41 RTCAlarm */ - unhandled_isr, /* 42 Reserved */ - unhandled_isr, /* 43 Reserved */ - unhandled_isr, /* 44 Reserved */ - unhandled_isr, /* 45 Reserved */ - unhandled_isr, /* 46 Reserved */ - unhandled_isr, /* 47 Reserved */ - unhandled_isr, /* 48 Reserved */ - unhandled_isr, /* 49 SDMMC1 */ - unhandled_isr, /* 50 Reserved */ - unhandled_isr, /* 51 SPI3 */ - unhandled_isr, /* 52 Reserved */ - unhandled_isr, /* 53 Reserved */ - unhandled_isr, /* 54 TIM6_DACUNDER */ - unhandled_isr, /* 55 TIM7 */ - unhandled_isr, /* 56 DMA2_CH1 */ - unhandled_isr, /* 57 DMA2_CH2 */ - unhandled_isr, /* 58 DMA2_CH3 */ - unhandled_isr, /* 59 DMA2_CH4 */ - unhandled_isr, /* 60 DMA2_CH5 */ - unhandled_isr, /* 61 Reserved */ - unhandled_isr, /* 62 Reserved */ - unhandled_isr, /* 63 Reserved*/ - unhandled_isr, /* 64 COMP */ - unhandled_isr, /* 65 LPTIM1 */ - unhandled_isr, /* 66 LPTIM2 */ - unhandled_isr, /* 67 USB_FS */ - unhandled_isr, /* 68 DMA_CH6 */ - unhandled_isr, /* 69 DMA_CH7 */ - unhandled_isr, /* 70 LPUART1 */ - unhandled_isr, /* 71 QUADSPI */ - unhandled_isr, /* 72 I2C3_EV */ - unhandled_isr, /* 73 I2C3_ER */ - unhandled_isr, /* 74 SAI1 */ - unhandled_isr, /* 75 Reserved */ - unhandled_isr, /* 76 SWPMI1 */ - unhandled_isr, /* 77 TSC */ - unhandled_isr, /* 78 Reserved */ - unhandled_isr, /* 79 AES */ - unhandled_isr, /* 80 RNG */ - unhandled_isr, /* 81 FPU */ - unhandled_isr /* 82 CRS */ -}; - -/* - * Does nothing ... forever. - */ -void unhandled_isr() -{ - __IO gpio_port_t* port_b = enable_gpio(GPIO_PORT_B); - gpio_output_pin_t pin3 = set_gpio_pin_output(port_b, PIN_3); - for (;;) { - /* Flash in a distinct pattern to know that something went wrong. */ - - pin_off(pin3); - delay(1000000); - pin_on(pin3); - delay(1000000); - pin_off(pin3); - delay(1000000); - pin_on(pin3); - delay(5000000); - } -} diff --git a/02.5-collatz/src/main.c b/02.5-collatz/src/main.c deleted file mode 100644 index 5af52ed..0000000 --- a/02.5-collatz/src/main.c +++ /dev/null @@ -1,93 +0,0 @@ - -#include "clock.h" -#include "delay.h" -#include "gpio.h" -#include "spin.h" -#include "usart.h" - -volatile uint32_t delay_amt = 20000000 / 4; - -int enable_usart2(uint32_t baud_rate) -{ - __IO gpio_port_t* port_a = enable_gpio(GPIO_PORT_A); - enable_hsi(&RCC, true); - - // Turn on the clock for the USART2 peripheral - set_usart2_clock_src(&RCC, USART_CLK_SRC_HSI16); - set_usart2_clock_enabled(&RCC, true); - - // Configure the I/O pins. Will use PA2 as TX and PA15 as RX so setup for - // alternate function - set_gpio_pin_mode(port_a, PIN_2, MODE_ALTERNATE); - set_gpio_pin_mode(port_a, PIN_15, MODE_ALTERNATE); - set_gpio_alternate_function(port_a, PIN_2, AFN_7); - set_gpio_alternate_function(port_a, PIN_15, AFN_3); - - // De-assert reset of USART2 - RCC.apb1rst1_r &= ~BIT(17); - - // Configure the USART - // disable USART first to allow setting of other control bits - // This also disables parity checking and enables 16 times oversampling - - USART2.c_r1 = 0; - USART2.c_r2 = 0; - USART2.c_r3 = 0; - - usart_set_divisor(&USART2, 16000000 / baud_rate); - usart_set_enabled(&USART2, USART_ENABLE_TX | USART_ENABLE_RX); -} - -int enable_usart1(uint32_t baud_rate) -{ - /* Enable the GPIO bus. */ - __IO gpio_port_t* port_b = enable_gpio(GPIO_PORT_B); - - /* Enable the USART clock. */ - RCC.apb2en_r |= BIT(14); - - /* == Configure the IO Pins. == */ - - /* GPIO D5 (Port B pin 6) is USART1 Tx, - * GPIO D6 (Port B pin 7) is USART1 Rx. */ - set_gpio_pin_mode(port_b, PIN_6, MODE_ALTERNATE); - set_gpio_pin_mode(port_b, PIN_7, MODE_ALTERNATE); - - /* Set the GPIO pins to use the USART alternate function. */ - set_gpio_alternate_function(port_b, PIN_6, AFN_7); - set_gpio_alternate_function(port_b, PIN_7, AFN_7); - - RCC.apb2rst_r &= ~BIT(14); /* De-assert reset of USART1 */ - - uint32_t baud_rate_div = 80000000 / baud_rate; - USART1.c_r1 = 0; - USART1.c_r2 = 0; - USART1.c_r3 = 0; - USART1.br_r = baud_rate_div; - - USART1.c_r1 |= BIT(3) | BIT(2); - USART1.c_r1 |= BIT(0); - - /* Enable the transmitter and the receiver. */ - usart_set_enabled(&USART1, USART_ENABLE_TX); - asm volatile(" cpsie i "); -} - -/* Main function. This gets executed from the interrupt vector defined above. */ -int main() -{ - /* Enable the GPIO port B. */ - - __IO gpio_port_t* port_b = enable_gpio(GPIO_PORT_B); - gpio_output_pin_t pin3 = set_gpio_pin_output(port_b, PIN_3); - gpio_output_pin_t pin1 = set_gpio_pin_output(port_b, PIN_1); - - /* Enable a higher clock frequency. */ - set_system_clock_MHz(80); - - enable_usart2(115200); - - pin_on(pin3); - usart_transmit_str(&USART2, "Hello, World\n"); - for(;;); -} diff --git a/02.5-collatz/src/spin.c b/02.5-collatz/src/spin.c deleted file mode 100644 index fbd16b6..0000000 --- a/02.5-collatz/src/spin.c +++ /dev/null @@ -1,49 +0,0 @@ -#include "spin.h" -#include "delay.h" -#include "gpio.h" - -#define SHORT_DELAY 200000 -#define LONG_DELAY (SHORT_DELAY * 2) - -static void flash_bit( - uint32_t base, gpio_output_pin_t out_pin, - uint8_t bit /* 0 => 0, non-zero => 1 */) -{ - pin_on(out_pin); - if (bit) { - delay(base * 2); - } else { - delay(base); - } - pin_off(out_pin); - delay(base); -} - -void spin(uint32_t base, uint8_t c) -{ - uint8_t code; - __IO gpio_port_t* port_b = enable_gpio(GPIO_PORT_B); - gpio_output_pin_t pin3 = set_gpio_pin_output(port_b, PIN_3); - - for (;;) { - code = c; - flash_bit(base, pin3, code & 0x80); - code <<= 1; - flash_bit(base, pin3, code & 0x80); - code <<= 1; - flash_bit(base, pin3, code & 0x80); - code <<= 1; - flash_bit(base, pin3, code & 0x80); - - code <<= 1; - flash_bit(base, pin3, code & 0x80); - code <<= 1; - flash_bit(base, pin3, code & 0x80); - code <<= 1; - flash_bit(base, pin3, code & 0x80); - code <<= 1; - flash_bit(base, pin3, code & 0x80); - - delay(base * 4); - } -} diff --git a/02.5-collatz/src/usart.c b/02.5-collatz/src/usart.c deleted file mode 100644 index eddfbe7..0000000 --- a/02.5-collatz/src/usart.c +++ /dev/null @@ -1,80 +0,0 @@ -#include "usart.h" -#include "delay.h" - -void set_usart1_clock_src(__IO rcc_t* rcc, usart_clk_src_t usart_clk_src) -{ - rcc->ccip_r = rcc->ccip_r & (~0x03) | usart_clk_src; -} - -void set_usart2_clock_src(__IO rcc_t* rcc, usart_clk_src_t usart_clk_src) -{ - rcc->ccip_r = rcc->ccip_r & ~(0x03 << 2) | (usart_clk_src << 2); -} - -void set_usart2_clock_enabled(__IO rcc_t* rcc, bool enable) -{ - if (enable) { - rcc->apb1en1_r |= BIT(17); - } else { - rcc->apb1en1_r &= ~BIT(17); - } -} - -void set_usart1_clock_enabled(__IO rcc_t* rcc, bool enable) -{ - if (enable) { - rcc->apb2en_r |= BIT(14); - } else { - rcc->apb2en_r &= ~BIT(14); - } -} - -void usart_set_parity(__IO usart_t* usart, usart_parity_t parity) -{ - uint32_t c_r1 = usart->c_r1; - c_r1 &= ~(0x3 << 9); - c_r1 |= parity; - usart->c_r1 = c_r1; -} - -void usart_set_enabled(__IO usart_t* usart, usart_enable_t enabled) -{ - uint32_t c_r1 = usart->c_r1; - - if (!enabled) { - usart->c1_bf.ue = 0; - } else { - /* Set the rx enabled. */ - usart->c1_bf.re = !!(enabled & USART_ENABLE_RX); - usart->c1_bf.te = !!(enabled & USART_ENABLE_TX); - usart->c1_bf.ue = 1; - } -} - -void usart_transmit_byte(__IO usart_t* usart, uint8_t byte) -{ - usart->td_r = byte; - /* Per the manual, when bit 7 of the IS register is set, then the usart - * data has been sent to the shift register. - * - * This bit is cleared by writing to the TD register. */ - while (!(usart->is_r & BIT(7))) - ; -} - -void usart_transmit_bytes(__IO usart_t* usart, const uint8_t* bytes, uint32_t n) -{ - while (n --) { - usart_transmit_byte(usart, *(bytes ++)); - } -} - -void usart_transmit_str(__IO usart_t* usart, const char* str) -{ - while (*str) { - if (*str == '\n') { - usart_transmit_byte(usart, '\r'); - } - usart_transmit_byte(usart, *(str ++)); - } -} diff --git a/02.5-collatz/src/vector.c b/02.5-collatz/src/vector.c deleted file mode 100644 index e69de29..0000000 --- a/02.5-collatz/src/vector.c +++ /dev/null |